Gasoline engine power grain mill
First, the advantages of gasoline engine grain mill:
1. Gasoline engine power, no electricity, suitable for mobile use.
2 , the body is light and compact, and the footprint is small .
3 , 7.5 horsepower brand motor, strong grinding power.
4 , the bottom of the "black" process, not easy to fade rust, beautiful appearance.
(Patent products, forgery must be investigated.)
Second, the function of the grain mill:
Cereals mill capable of a variety of food, medicines ground into a homogeneous powder 50 to 200 mesh
The working principle of the three-grain cereal mill:
The connecting shaft of the mill is directly connected to the motor shaft. When the motor starts running, the connecting shaft and the grinding disc that is placed on the connecting shaft are operated together. The material to be ground enters the milling sleeve from the hopper, the relative operation between the mandrel of the grinding disc and the grinding sleeve, and the crushing force causes the material to be broken into small pieces; the small particles after the grinding are brought into the spiral motion of the grinding disc. In the middle of the two grinding discs, the relative operation of the grinding flakes causes the material to be pulverized into fine particles (powder) in a short time; the powder flows out from the gully of the grinding disc and smashes to the periphery while being scraped on the grinding disc. Take the powder plate and take it out from the powder outlet. The machine is a continuous feeding operation, the structure is simple and generous, the noise is small, the operation is easy, and the crushing is delicate.
Four, five grains and coarse flour mill application range:
Applicable to supermarkets and shopping mall counters, grain processing shops, grain processing shops, etc.
Five, five grains and coarse flour mill processing range:
Food - sesame, walnut, rice, black rice, soybeans, mung beans, peanuts, lotus seeds, corn, sorghum, barley, buckwheat, oats, etc.;
Medicinal materials - almonds, alfalfa, red dates, medlar, medlar, coix seed, hawthorn, yam, shouwu, red beans, frankincense, dodder, angelica, codonopsis, scutellaria, etc.;
Chemicals - non-corrosive soft ores.
Sixth, gasoline engine power grain mill grinding machine technical parameters:
Model Model | MF-168 ( 304S.S ) | |
Dynamic power Power | 6HP | 7.5HP |
Zui high power and corresponding speed Max power and speed KW / ( r / min ) | 3.05/3600 | 5.5/3600 |
Zui low no-load stable speed (idle speed) ( r/min ) | ≤ 1400 | |
Fuel consumption rate Fuel consumption ( g/(KW.h) ) | ≤ 395 | |
Oil consumption rate Oil consumption ( g/(KW.h) ) | ≤ 6.8 | |
Fineness Fineness (mesh) | 50~200 mesh | |
Production capacity output ( kg / h ) | 20~40kg/h | |
Dimension Dimension ( mm ) | 400 × 550 × 740mm | |
Weight Weight ( kg ) | 45kg | 61Kg |
Startup method: | Hand pull | Hand pull + electronic fire |
Adjustable resistance: | Fast and slow feed the material thickness can be adjusted | |
Price: Price | Power Conference | Power Conference |
Seven, Chongqing Rui Nao gasoline mill electronic ignition features:
1 , the power is greater ( 7.5 horses) ;
2 , comes with charging function ;
3 , can be used for flashlight ;
4 , the electronic start control panel and the machine head integrated (reasonable structure, easy to operate) the first in the country ;
4 , the sound is quieter than similar domestic machines .
Eight, mill operation and adjustment
1. The mill should be placed on a fixed, solid horizontal table or table, and thick solid wood is better. The iron plate under the motor has 4 screw holes. Use long screws to screw the motor iron plate firmly on the table or table (cabinet); if there is soft rubber (rubber pad) between the motor and the table, Reduce vibration and achieve better mute effect.
2 , the motor cover should also be fixed on the table or cabinet, the motor cover and the motor iron plate should be separated, not close to the iron plate, to prevent the iron plate and the motor cover from vibrating and resonating after the start-up operation, and then the motor cover is locked with a short screw. tight.
3. Open the cover, fix the grinding disc on the connecting shaft, and press it on the grinding disc with two thumbs. If the grinding disc can be freely stretched, the grinding disc and the connecting shaft are well fitted. Then cover the cover, tighten the lock nut, connect the power supply, open the switch, check whether the mill is running in the specified direction, whether the sound and vibration are normal. If there is abnormal noise or abnormal vibration, shut down and check the problem until the problem is solved. Normal to restart.
4 , start the power supply, run for about 1 minute, put the material into the hopper, screw the regulator to the appropriate position, open the blanking baffle, and let the material flow slowly into the milling cavity. The baffle is opened a little to avoid feeding too fast and jamming the motor. Ordinary materials are generally ground twice, with coarse grinding and fine grinding for the second time.
5 , the thickness of the grinding powder depends on the gap between the two grinding pieces, and the clearance of the grinding plate is controlled by the adjuster, according to the thickness indication on the cover, when the adjuster is adjusted in the fine direction, the two grinding pieces The gap is reduced and the grinding becomes finer; on the contrary, the grinding becomes thicker.
6. How to control the adjustment range and strength of the regulator can be determined by the sound produced by the friction of the ear and the sound of the motor running. The tighter the grinding blade is, the louder and sharper the sound is. If it is not tight or separated, the sound will be soft.
7. Separately grind materials with particularly high oil content such as sesame, walnut, peanut, etc., because such materials have a particularly high oil content, which can only be ground into coarse powder, finely ground, and a large amount of oil permeates out, which will turn the powder into a slurry. shape. Therefore, when grinding materials with particularly high oil content, the regulator should not be adjusted too tightly, and the gap between the grinding discs should be kept close or even completely separated to be ground into powder (small granular shape). If the above materials need to be ground very fine, it needs to be equipped with oil-free or low-oil content materials. The ratio of high oil content and low (none) oil content is: 1 : 4 to 1 : 5 , and the method of grinding twice is adopted. Rough grinding, grinding the second time.
8. Loading and unloading of moving and static grinding discs: the moving grinding discs are mounted on the grinding discs, and the static grinding discs are installed in the grinding chamber. Remove the 3 screws of the fixed grinding disc and remove the grinding disc. The material of the grinding disc is pig iron, and the hardness of the pig iron is about 52 °, the hardness is large, and the elasticity is poor. When installing the grinding disc, the screw should not be tightened too tightly to prevent the grinding disc from breaking.
Nine, operating methods and techniques
(1) Operation method
1. Before using the machine every day, it is necessary to check whether the machine is running normally, whether the screws of the static grinding disc and the moving grinding disc are loose and tightened.
2 , the dry material needs to be milled twice, the second rough grinding, the second fine grinding.
When rough grinding, grinding to adjust the adjustment screws slightly squeaky frictional sound, and then further adjusted back to just no coarse friction sound, and a discharge port plate interposed / 2-1 / 3 to the open.
3 , dry dry fueling mixed materials
Method one :
Grinding dry oily mixed materials requires two grindings, a second coarse grinding, and a second fine grinding.
When rough grinding, adjust the adjusting screw to the grinding plate to have a slight rubbing sound, then adjust the adjusting screw one turn to the coarse back, and then completely open the lower cutting insert; (the ground material is almost half a grain size) . When fine grinding, adjust the adjusting screw to the grinding piece to have a slight rubbing sound and then open the lower part of the inserting plate 1/4-1/3 .
Method two :
The first finely ground dry material (dry material and grinding the same method of operation). Then mix the dried dry material with the oily material evenly, adjust the adjusting screw to the grinding piece to have a slight rubbing sound, and then open the lower opening 1/4-1/3 .
4 , grinding materials with high sugar content
When grinding high-sugar materials, (such as red dates, kumquat tablets, wolfberry, etc.) high-sugar materials need to be baked, dehydrated, or frozen for more than two hours to grind , only need to grind once, adjust the adjustment Screw to the grinding pad just has a slight rubbing sound, then open the lower mouth insert, (single grinding of the carrots requires two grindings, the second coarse grinding and grinding dry materials are the same as the coarse grinding operation, the second The fine grinding adjustment adjustment screw to the grinding piece just has a rubbing sound, and then open the lower opening plate 1/4-1/3 .)
5. Grinding the mixed material with high sugar content, the operation method is the same as that of the dry oily mixed material.
(2) Replace the grinding disc
1. Remove the old grinding disc (the grinding disc has the front and back sides, and the static grinding disc and the moving grinding disc can be exchanged for use).
2. Install the grinding disc, adjust the gap between the inner hole of the grinding disc and the grinding sleeve or the grinding disc, and then tighten the screw.
3. Adjust the flatness of the grinding plate: Turn on the machine, adjust the adjusting screw to the grinding piece to make a very harsh sound, run for 20-30 seconds, stop the front end cover, take out the moving grinding disc, and gently touch the static grinding piece around the hand. The temperature to which the position is high or the temperature is low, the position of the high temperature indicates that the grinding plate is high, and the position with low temperature indicates that the grinding piece is low, (or where the position of the grinding blade is bright or not polished, bright The position of the position is high, and the position of the non-lighting is low. ) The high position tightens the screw of the fixed grinding plate, the lower position fixes the screw of the fixed grinding piece, and then turns on the machine to repeat the above operation until the grinding piece is flat. , tighten the screws.
(3), grinding and grinding
Take 2-3 kg of rice into the funnel, start the machine to adjust the adjusting screw to the grinding piece, just have a slight rubbing friction sound, and then adjust the adjusting screw 1/3-2/3 turn finely , the grinding piece has a harsh rubbing friction Sound, open the lower mouth insert 1/2-1/3 , repeat the milled rice flour back to the funnel mill for 15-20 minutes, then take about 2 or so of the rice according to the method of grinding dry materials, try to grind Whether the rice flour has reached the fineness requirement, if the fineness requirement is not met, repeat the above operation.
Applicator,Medical Dressing,Waterproof Wound Dressing,Wound Care Dressings
Henan Maidingkang Medical Technology Co.,Ltd , https://www.mdkmedical.com