1 , the bottle screw is dislocated
* Use the wrench to loosen the fastening bolts, adjust the rotary screw to the good position of the Zui, first tighten a bolt, jog the running observation effect, and tighten the other bolts when the position is appropriate.
2 , in and out of the bottle star wheel misplacement
* Loosen the bolts of the star wheel and adjust it to the good position of Zui. If necessary, loosen the bolt at the bottom of the star wheel.
3 , the hub clamp label refers to loose
* When the single clip is loose, loosen the fastening screw and push the label paper to the appropriate position to tighten the screw.
* When the whole clamp is loose, loosen the bolts of the clamped shaft, turn the hub to the appropriate position, push the clamp to the inside to the position of the Zui, and tighten the bolts.
4 , the hub clamp label refers to the standard
*The hub spring is broken and can be replaced.
*The tension spring force is invalid, you can replace it.
5 , Labeling paper skew
* Adjust the height of the label box according to the position of the label paper on the target board
6 , labeling paper folds, uneven
* Adjust the thickness of the film on the rubber roller
* Adjust the position of the brush
7 , labeling paper warp angle, flash edge
* The target board is not evenly glued, adjust the position of the target board to make it evenly glued.
* Adjust the position of the brush
8 , the target residue mark paper
*The clip is loose, and the position of the clip is adjusted.
* Adhesive viscosity is too large, adjust the glue temperature
*There is less glue on the left side of the target board, which causes the label paper to tilt up and adjust the target position.
9 ã€Running the bottle during the top labeling
* Check if the position of the pressure head is suitable and adjust its position.
* Check if the balls in the bottle head are missing, which makes the bottle rotation inflexible.
* Check if the back plate behind the bottle at the transfer hub is in place, adjust it.
10 , Sharp corners and not attached to the standard body when the top mark Topmark
* Adjust the hub with the handwheel to rotate it back and forth to adjust it to the proper position.
* Adjust the angle between the top mark and the body mark
11 ã€The cover is covered when the top label is attached.
* Adjust the angle of the stick to the right position
12 , the top mark is damaged after the head is damaged or the top is not correct
* Replace the sponge pad and rubber spring pad in the head unit
13 , the pump pumping amount is small or blocked
* Check if there is any debris in the pump bottom
* Check if the foreign matter is clogged in the hose
* Check the position of the steel ball, whether the pump leaks
14 ã€Top mark indentation misalignment
* Loosen and fasten the tightened middle shaft, loosen and tighten the bolts of the tension sleeve to loosen it with the shaft, and adjust the rotary head to the appropriate position.
15 , Top label paper is not wrapped tightly
*The target board is not enough glue, adjust the target position
* Check the position of the brush and adjust it
16 , top mark tearing
* Adjust the thickness of rubber roller film
* Check whether the label finger movement is consistent or not.
17 ã€Back label and body are uneven on both sides
* Adjust the hub with the handwheel to rotate it before and after, and adjust it to the proper position.
18 , poor cosmetic results
* Check the belt position and adjust it to the proper position
* Whether the cosmetic nozzle is blocked or not
19 , the code is not clear, the position is not centered
* Check if there are foreign objects or water drops on the cap and adjust the position of the blow pipe.
* Check if the nozzle is clean, rinse the nozzle
* Adjust the position of the nozzle to center it
20 , the machine is running suddenly Downtime
* Whether there is a frying bottle to blast the protective door and close the protective door
* Whether there is no wine in the front chain or the chain is blocked
*If there is no cover bottle, enter the standard machine and take it out.
Green wheat flour is made from green wheat, and wheat tastes good. From the perspective of traditional Chinese medicine, its medicinal properties are relatively cool. Besides, it can enter the heart, spleen and kidney meridians. These are all Chinese medicine doctors. The expressed efficacy of wheat, and after being eaten by people, wheat can nourish the heart and nourish the kidneys, nourish the spleen, stomach, stomach, etc., and can also remove heat and quench thirst. This is very meaningful for people's health, especially for the elderly, the various bodily functions of the elderly will be affected to some extent, and eating some flour at this time can moisturize The functions of various body organs are very helpful to their bodies.
Dehydrated Green Wheat Flour,Green Wheat Grass Powder,Natural Organic Wheat Grass Powder,100% Original Wheat Grass Powder
Laian Xinshuyu Food Co., Ltd , https://www.xinshuyufood.com