The sugar-coated machine is a machine for the pharmaceutical industry to uniformly coat and polish the formed chips, and can also be used for the candy mechanism pill or coating in the food industry.
The working principle is that the chip is evenly coated with the coating crystal on the surface as soon as possible, and the purpose of polishing is achieved, and the syrup compounding slurry must be sprayed on the chips in the pot by manual operation. By rotating the pot clockwise, the sugar-coated pieces are tumbled in the pot, and the friction-grinding is evenly distributed on all the chips. At the same time, the hot air is passed into the pot, and the surface water of the tablet can be quickly removed, and the finished sugar-coated tablets and the like are obtained after the Zui.
Installation and use 1. Turn on the power. Note: The phase and neutral lines cannot be connected incorrectly.
2. Connect the air source to the air pipe joint on the lower side of the machine through the Φ8PU pipe.
3. A coating liquid is added to the liquid cylinder.
4. Turn on the power switch and turn on the power at this time.
5. Adjust the main engine speed according to the instructions of the main governor.
6. Open the inlet air adjustment switch and the inlet fan starts working.
7. Adjust the temperature controller to adjust the temperature to the temperature you need. At this time, if the actual temperature is lower than the set value, the heater power is turned on and the heater starts to heat up. If the actual temperature is higher than the set value, the heater power is turned off and the heater stops heating.
8. Open the gun switch and the gun starts working. Refer to the gun manual for the use of the gun.
9. After the above functions are properly adjusted, the air compressor can be turned on, and the air pressure is about 4 to 6 kg/cm3.
Sugar-coated machine, widely used in pharmaceutical, chemical, food, research, hospitals for tablets, pills, sugar coating, polishing and rolling food, can also be used in scientific research units to try new drugs.
The working principle is that the chip is evenly coated with the coating crystal on the surface as soon as possible, and the purpose of polishing is achieved, and the syrup compounding slurry must be sprayed on the chips in the pot by manual operation. By rotating the pot clockwise, the sugar-coated pieces are tumbled in the pot, and the friction-grinding is evenly distributed on all the chips. At the same time, the hot air is passed into the pot, and the surface water of the tablet can be quickly removed, and the finished sugar-coated tablets and the like are obtained after the Zui.
Installation and use 1. Turn on the power. Note: The phase and neutral lines cannot be connected incorrectly.
2. Connect the air source to the air pipe joint on the lower side of the machine through the Φ8PU pipe.
3. A coating liquid is added to the liquid cylinder.
4. Turn on the power switch and turn on the power at this time.
5. Adjust the main engine speed according to the instructions of the main governor.
6. Open the inlet air adjustment switch and the inlet fan starts working.
7. Adjust the temperature controller to adjust the temperature to the temperature you need. At this time, if the actual temperature is lower than the set value, the heater power is turned on and the heater starts to heat up. If the actual temperature is higher than the set value, the heater power is turned off and the heater stops heating.
8. Open the gun switch and the gun starts working. Refer to the gun manual for the use of the gun.
9. After the above functions are properly adjusted, the air compressor can be turned on, and the air pressure is about 4 to 6 kg/cm3.
Sugar-coated machine, widely used in pharmaceutical, chemical, food, research, hospitals for tablets, pills, sugar coating, polishing and rolling food, can also be used in scientific research units to try new drugs.
Spacer and Bushing
The Spacers are designed to hold materials a predetermined distance away from the surface they are mounted to, or mount two items a set distance apart. Sizes and materials vary depending on intended use.
The Bushings are used as spacers between pulleys and gears to prevent damage caused by vibration and dynamic loads. The durable bushing material is corrosion resistant.
The
material of Spacer Bushing including carbon steel, Stainless Steel, Aluminum
and Brass. Dimensions are according to custom made. The zinc-plated finish
provides some corrosion resistance.
Spacer & Bushing,Spacer Bushing,Shaft Spacer, Bushing Spacer
Ningbo Yokelink Machinery Co.,Limited , https://www.yokelink.com